[Hai-users] Z-Wave and Omni

[Dan Wright]

The Application Guide is not out yet per my distributor.

Tom Morgan at Worthington would be the best to ask about Z-wave/HAI
integration, but I assume he is at EHX in Orlando this week.

The new Levtion ViziaRF wall pads (area and scene controllers) are going to
be a great way to do lighting control.  They are just reaching the market
now.  



> -----Original Message-----
> From: hai-users-bounces at tssi.com [mailto:hai-users-bounces at tssi.com] On
> Behalf Of Dan Hoehnen
> Sent: Saturday, March 03, 2007 5:04 AM
> To: hai-users at tssi.com
> Subject: [Hai-users] Z-Wave and Omni
> 
> All,
> 
> Has anyone gotten an OP2 to control any zwave devices yet?  I have all the
> parts, but am not able to control a zwave lamp module from my OP2.  Here
> is
> a description of what I have done...
> 
> First, it works fine when using the Leviton ViziaRF handheld controller,
> so
> I know the zwave basics are correct.
> 
> I am using a ViziaRF lamp module (RZP03) and handheld controller (RZCPG)
> and
> RS232 interface (RZC0P).
> 
> I have firmware 2.14 and PC Access 2.14.  I created a new file in PC
> Access,
> setup house codes 1-4 as zwave, named UNIT 2 as "node 2", and in
> Setup/Installer/Control, on the "ViziaRF Z-Wave Node IDs" tab I set unit 2
> to have a node ID of 2.  All other units have a 0 for their node ID.
> Serial
> port #2 is setup for zwave at 9600 baud and is connected to the zwave
> rs232
> interface.
> 
> The ViziaRF lamp module is programmed as node 2 and the handheld
> controller
> can turn it on and off using the #1 ON and #1 OFF buttons on the
> controller
> (area 1).
> 
> There is no documentation with the RS232 interface.  There is nothing in
> the
> HAI 2.14 installation manual or release notes about configuring the RS232
> interface.  The ViziaRF handheld remote doc's have a SMALL section on HAI,
> but refers to a ViziaRF Application Guide, which I don't have and can't
> find
> online.
> 
> By playing around I found that by holding in the button on the RS232
> interface that the light would change from blinking green to solid yellow.
> I then used the handheld remote to program it into the system as a
> controller.  So, my RS232 interface is now node 3.  I can then go to the
> advanced setup screen in the handheld controller, choose HAI Setup, and
> see
> node 3 listed.  It looks like I can then associate node 3 with both the
> handheld remote and node 2 (lamp module).  The handheld remote seems to go
> through a successful setup sequence when associating node 2 with the rs232
> interface, but commands from PCAccess  or an OmniTouch to control node 2
> never work.
> 
> When I go back into the HAI Setup in the handheld controller, node 2 is
> never CHECKED as being associated.  So, maybe I am just not saving the
> setup?  But, there is never a SAVE option.
> 
> Ideas?  Any doc's on setting up EVERYTHING in order to get an OP2 to use
> ViziaRF devices?
> 
> Regards,
> Dan Hoehnen
> Custom Automation Technologies, Inc.
> 
> 
> 
> _______________________________________________
> HAI-users mailing list
> HAI-users at tssi.com
> http://romaine.tssi.com/mailman/listinfo/hai-users