[Hai-users] Z-Wave and Omni

[Dan Hoehnen]

Yep, if it wasn't the weekend I'd be trying to talk to Tom.  I have one of
the keypads too, but have not tried to use it.  My immediate need is to have
an Omni control zwave devices. 

Regards,
Dan 


-----Original Message-----
From: Dan Wright [mailto:dan at starwolfsystems.com] 
Sent: Saturday, March 03, 2007 10:16 AM
To: 'Dan Hoehnen'; hai-users at tssi.com
Subject: RE: [Hai-users] Z-Wave and Omni

The Application Guide is not out yet per my distributor.

Tom Morgan at Worthington would be the best to ask about Z-wave/HAI
integration, but I assume he is at EHX in Orlando this week.

The new Levtion ViziaRF wall pads (area and scene controllers) are going to
be a great way to do lighting control.  They are just reaching the market
now.  



> -----Original Message-----
> From: hai-users-bounces at tssi.com [mailto:hai-users-bounces at tssi.com] 
> On Behalf Of Dan Hoehnen
> Sent: Saturday, March 03, 2007 5:04 AM
> To: hai-users at tssi.com
> Subject: [Hai-users] Z-Wave and Omni
> 
> All,
> 
> Has anyone gotten an OP2 to control any zwave devices yet?  I have all 
> the parts, but am not able to control a zwave lamp module from my OP2.  
> Here is a description of what I have done...
> 
> First, it works fine when using the Leviton ViziaRF handheld 
> controller, so I know the zwave basics are correct.
> 
> I am using a ViziaRF lamp module (RZP03) and handheld controller 
> (RZCPG) and
> RS232 interface (RZC0P).
> 
> I have firmware 2.14 and PC Access 2.14.  I created a new file in PC 
> Access, setup house codes 1-4 as zwave, named UNIT 2 as "node 2", and 
> in Setup/Installer/Control, on the "ViziaRF Z-Wave Node IDs" tab I set 
> unit 2 to have a node ID of 2.  All other units have a 0 for their 
> node ID.
> Serial
> port #2 is setup for zwave at 9600 baud and is connected to the zwave
> rs232
> interface.
> 
> The ViziaRF lamp module is programmed as node 2 and the handheld 
> controller can turn it on and off using the #1 ON and #1 OFF buttons 
> on the controller (area 1).
> 
> There is no documentation with the RS232 interface.  There is nothing 
> in the HAI 2.14 installation manual or release notes about configuring 
> the RS232 interface.  The ViziaRF handheld remote doc's have a SMALL 
> section on HAI, but refers to a ViziaRF Application Guide, which I 
> don't have and can't find online.
> 
> By playing around I found that by holding in the button on the RS232 
> interface that the light would change from blinking green to solid yellow.
> I then used the handheld remote to program it into the system as a 
> controller.  So, my RS232 interface is now node 3.  I can then go to 
> the advanced setup screen in the handheld controller, choose HAI 
> Setup, and see node 3 listed.  It looks like I can then associate node 
> 3 with both the handheld remote and node 2 (lamp module).  The 
> handheld remote seems to go through a successful setup sequence when 
> associating node 2 with the rs232 interface, but commands from 
> PCAccess  or an OmniTouch to control node 2 never work.
> 
> When I go back into the HAI Setup in the handheld controller, node 2 
> is never CHECKED as being associated.  So, maybe I am just not saving 
> the setup?  But, there is never a SAVE option.
> 
> Ideas?  Any doc's on setting up EVERYTHING in order to get an OP2 to 
> use ViziaRF devices?
> 
> Regards,
> Dan Hoehnen
> Custom Automation Technologies, Inc.
> 
> 
> 
> _______________________________________________
> HAI-users mailing list
> HAI-users at tssi.com
> http://romaine.tssi.com/mailman/listinfo/hai-users