[Hai-users] RC80 thermostat

[Wijoyo Utomo]

Hi Darren,

Not much luck with displaying outside temperature... But got link from
Byron which tells how to change the displayed unit on the thermostat and
it works great (thanks Byron.. grin..)

Here it is  http://www.milehighautomation.com/downloads/rci80.pdf
Hope that helps.

Best Regards,
W. Utomo


> -----Original Message-----
> From: hai-users-bounces at tssi.com 
> [mailto:hai-users-bounces at tssi.com] On Behalf Of Darren and Jody Bzdel
> Sent: Tuesday, August 01, 2006 8:48 PM
> To: 'Tony Golden'; hai-users at tssi.com
> Subject: RE: [Hai-users] RC80 thermostat
> 
> 
> I had to double check my wiring a few times before it started 
> to work properly. Once it was hooked up correctly the 
> temperature cycled as expected. Is it possible to try the 
> sensor with a short wire near the unit to verify the sensor 
> is working?
> 
> I have also tried to setup my RC-80 to show in Celsius. I 
> have changed the setting so the panel reports in C, and when 
> I check the status over the phone it is also in C, but the 
> tstat still shows F. I talked to a HAI guru and his answer 
> was the same - you can do it, but I am not sure how. The 
> manual does not say, so if anyone knows how to do it - it 
> would be  much appreciated.
> 
> -----Original Message-----
> From: hai-users-bounces at tssi.com 
> [mailto:hai-users-bounces at tssi.com] On Behalf Of Tony Golden
> Sent: August 1, 2006 6:27 AM
> To: hai-users at tssi.com
> Subject: RE: [Hai-users] RC80 thermostat
> 
> I'm sure there's a way to display Celsius, but don't remember 
> the exact configuration.  If you can't find it in the panel's 
> and thermostat's owners manuals, check with HAI's tech support.
> 
> For the outside temperature, first verify the sensor's 
> actually working, by viewing the status on the keypad.  If 
> the temperature shows correctly on the keypad, then it's 
> working/connected properly.  If it doesn't, it could be wired 
> incorrectly, configured for the wrong type (Extended or not), 
> or the sensor could be defective.
> 
> If the outside temperature does display correctly on the 
> keypad, there may be a problem with the thermostat's 
> communication with the panel.  See if you can view the 
> thermostat's status from a keypad, and also control it.  If 
> you can't do one, or both, there's a problem with the wiring, 
> the panel's or thermostat's configuration, or the thermostat. 
>  It's also remotely possible the panel itself could be 
> defective, but that's the least-likely scenario -- I'd rule 
> out all the other possibilities, first...
> 
> 
> -----Original Message-----
> From: hai-users-bounces at tssi.com 
> [mailto:hai-users-bounces at tssi.com] On Behalf > Of Wijoyo Utomo
> 
> Sent: Tuesday, August 01, 2006 4:45 AM
> To: hai-users at tssi.com
> Subject: [Hai-users] RC80 thermostat
> 
> I have an RC80 and would like to know how to change the 
> displayed temperature into Celcius instead of Fahrenheit. 
> Also would like to know how to display the "OUTSIDE" 
> temperature on the thermostat. I have set one zone to be 
> Outdoor Temperature and name the zone OUTDOOR, but the 
> thermostat does not cycle the display between the outside and 
> current as per instruction manual.
> 
> Thanks in advance.
> 
> Rgds,
> W. Utomo
> 
> 
> _______________________________________________
> HAI-users mailing list
> HAI-users at tssi.com http://romaine.tssi.com/mailman/listinfo/hai-users
> 
> _______________________________________________
> HAI-users mailing list
> HAI-users at tssi.com http://romaine.tssi.com/mailman/listinfo/hai-users
>