[Hai-users] Re: HAI-users Digest, Vol 31, Issue 3

[Brad]

It is recommended by HAI that all UPB installs have a coupler.

----- Original Message ----- 
From: "Dave Kalata" <dave at kalata.net>
To: <hai-users at tssi.com>
Sent: Friday, May 25, 2007 8:36 AM
Subject: [Hai-users] Re: HAI-users Digest, Vol 31, Issue 3


> My understanding, limited though it may be, is that UPB doesn't have the 
> same need for a phase coupler that X10 uses. In most cases, the signal 
> will simply travel out to the transformer and then back down the other 
> line for your other phase. In very small instances, a phase coupler would 
> be required.
>
> Dave
>
> ----- Original Message ----- 
> From: <hai-users-request at tssi.com>
> To: <hai-users at tssi.com>
> Sent: Friday, May 25, 2007 2:00 AM
> Subject: HAI-users Digest, Vol 31, Issue 3
>
>
>> Send HAI-users mailing list submissions to
>> hai-users at tssi.com
>>
>> To subscribe or unsubscribe via the World Wide Web, visit
>> http://romaine.tssi.com/mailman/listinfo/hai-users
>> or, via email, send a message with subject or body 'help' to
>> hai-users-request at tssi.com
>>
>> You can reach the person managing the list at
>> hai-users-owner at tssi.com
>>
>> When replying, please edit your Subject line so it is more specific
>> than "Re: Contents of HAI-users digest..."
>>
>>
>> Today's Topics:
>>
>>   1. Upgrading to UPB (Guy Wenzel)
>>   2. Re: Upgrading to UPB (Ahmed Al-Saggaf)
>>
>>
>> ----------------------------------------------------------------------
>>
>> Message: 1
>> Date: Thu, 24 May 2007 13:36:30 -0500
>> From: "Guy Wenzel" <guy at Oakguy.com>
>> Subject: [Hai-users] Upgrading to UPB
>> To: <hai-users at tssi.com>
>> Message-ID: <1658D67D2D1FF7448B24DC2210F9365D250D at iceman.Oakguy.com>
>> Content-Type: text/plain; charset="us-ascii"
>>
>> Gentlemen
>>
>> I am upgrading after three years to UPB.  Things have been good up till
>> now.  I installed the new firmware, switches and PIM.  I can tell
>> through web link that signals are going out since the PIM flashes red.
>> I set the switches to learn and go to the controller and do the 6 > 1 to
>> discover the switch and it fails.  I set Serial port 3 to UPB.  House
>> Code 1 to HLC Lighting through the controller keypad since my PC Access
>> is end user 2.7 (ugh).
>>
>>
>>
>> I got a UPB training pdf file from Worthington that explains setting up
>> HLC lighting for the units.  That's what I don't understand.  How that
>> connection works since I don't have any keypads yet.  I did not add a
>> coupler yet since I thought UPB did not need one but I should get
>> something to recognize right?  I'm getting one on order now.
>>
>>
>>
>> Any ideas?
>>
>> Thanks
>>
>> -g
>>
>> -------------- next part --------------
>> An HTML attachment was scrubbed...
>> URL: 
>> http://romaine.tssi.com/pipermail/hai-users/attachments/20070524/f13f51ee/attachment-0001.htm
>>
>> ------------------------------
>>
>> Message: 2
>> Date: Thu, 24 May 2007 17:34:44 -0700 (PDT)
>> From: Ahmed Al-Saggaf <sagsag77 at yahoo.com>
>> Subject: Re: [Hai-users] Upgrading to UPB
>> To: Guy Wenzel <guy at oakguy.com>, hai-users at tssi.com
>> Message-ID: <750386.89175.qm at web30512.mail.mud.yahoo.com>
>> Content-Type: text/plain; charset="iso-8859-1"
>>
>> As far as I understand, UPB needs a phase coupler, and that could be the 
>> problem.
>>  Someone can correct me.
>>  Ahmed Al-Saggaf.
>>
>> Guy Wenzel <guy at oakguy.com> wrote:
>>        st1\:*{behavior:url(#default#ieooui) }                Gentlemen
>>  I am upgrading after three years to UPB.  Things have been good up till 
>> now.  I installed the new firmware, switches and PIM.  I can tell through 
>> web link that signals are going out since the PIM flashes red.  I set the 
>> switches to learn and go to the controller and do the 6 > 1 to discover 
>> the switch and it fails.  I set Serial port 3 to UPB.  House Code 1 to 
>> HLC Lighting through the controller keypad since my PC Access is end user 
>> 2.7 (ugh).
>>
>>  I got a UPB training pdf file from Worthington that explains setting up 
>> HLC lighting for the units.  That's what I don't understand.  How that 
>> connection works since I don't have any keypads yet.  I did not add a 
>> coupler yet since I thought UPB did not need one but I should get 
>> something to recognize right?  I'm getting one on order now.
>>
>>  Any ideas?
>>  Thanks
>>  -g
>>
>> _______________________________________________
>> HAI-users mailing list
>> HAI-users at tssi.com
>> http://romaine.tssi.com/mailman/listinfo/hai-users
>>
>>
>>
>> ---------------------------------
>> No need to miss a message. Get email on-the-go
>> with Yahoo! Mail for Mobile. Get started.
>> -------------- next part --------------
>> An HTML attachment was scrubbed...
>> URL: 
>> http://romaine.tssi.com/pipermail/hai-users/attachments/20070524/b5e0e16e/attachment-0001.htm
>>
>> ------------------------------
>>
>> _______________________________________________
>> HAI-users mailing list
>> HAI-users at tssi.com
>> http://romaine.tssi.com/mailman/listinfo/hai-users
>>
>>
>> End of HAI-users Digest, Vol 31, Issue 3
>> ****************************************
>
>
> _______________________________________________
> HAI-users mailing list
> HAI-users at tssi.com
> http://romaine.tssi.com/mailman/listinfo/hai-users